Skip to content

Accessories: clamping

Welding table clamps and quick-release clamping bolts

Welding table clamps press the workpiece onto the table, quick-release clamping bolts connect stops and squares to the top. Both sit directly in the 28 mm holes. For the bolt, the thickness of the table top decides: there are separate versions for PRO tables with 25 mm and for Standard tables with 15 mm.

Request a quoteView clamps in the online shop (German)

Professional 90 degree screw clamp with spindle and red handle, inserted into a hole in the welding table plate

In short: To clamp on the hole grid you need two parts: professional screw clamps with spindle, which clamp components up to 200, 240 or 340 mm high, and quick-release clamping bolts with 28 mm diameter. The clamps are pushed through a hole; choose the quick-release clamping bolts to match a 15 or 25 mm table top.

Professional welding clamps 90° and 45° with spindle

The professional screw clamps from die schmiede are pushed through a 28 mm hole and can be rotated steplessly through 360°, so the clamping arm can point in any direction.

The pressure comes from a spindle; according to the shop, this clamps components precisely and firmly, horizontally as well as vertically. The clamps are nitrided and marked System 28. Three versions are available:

Professional screw clamps with spindle for the 28 mm hole grid (data from the shop)
ModelDimensionsMax. clamping heightWeightArt. no.
Professional screw clamp 90°290 x 240 mm200 mm2.3 kg28-4-0005
Professional screw clamp 90°, high clamping range370 x 240 mm340 mm2.7 kg28-4-0008
Professional screw clamp 45°300 x 240 mm240 mm2.3 kg28-4-0006

For workshops with several workstations, the special offers include a set of 10 of the 90° clamp and a set of 5 of the 45° clamp. According to the set descriptions, the screw clamps in accessory sets 1.0 to 4.0 measure 210 x 260 mm.

Quick-release clamping bolts: versions for PRO or Standard

A quick-release clamping bolt connects two components, typically a stop or square to the table top. It is inserted and locked by a twist lock with locking balls.

Because the bolt passes through the top, it comes in two versions: for PRO tables with a 25 mm and for Standard tables with a 15 mm table top. The shop lists the same length and specifications for both versions, so tell them apart by product title and article number when ordering.

Blackened quick-release clamping bolt with twist lock and 28 mm diameter
Short quick-release clamping bolt, blackened, 28 mm diameter

For PRO tables (25 mm)

For Standard tables (15 mm)

Diameter
28 mm
Length
95 mm
Shear force
220 kN
Tensile force (steel)
25 kN
Tightening torque
25 Nm

Both versions are blackened. The specifications are manufacturer data from the shop.

Magnetic clamping bolts, connecting bolts and countersunk clamping bolts

For special tasks there are three further bolts which, according to the shop, are designed for PRO tables with a 25 mm top.

The aluminium magnetic clamping bolt clamps without tools and is suitable for pressure-sensitive parts or places where no counterhold is possible. Connecting bolts and countersunk clamping bolts create concealed connections: the connecting bolt between the welding table and a construction bridge, the countersunk clamping bolt for the cast PRO clamping squares.

Aluminium magnetic clamping bolt for welding tables
Aluminium magnetic clamping bolt, shank length 25 mm
Special bolts for PRO welding tables (data from the shop)
BoltPurposeLength, clamping rangeSpecificationsArt. no.
Magnetic clamping bolt, aluminiumClamping without tools, for pressure-sensitive parts68 mm, shank length 25 mmWeight 0.09 kg28-4-0010-25
Short connecting bolt, blackenedConcealed connection of 2 components, such as welding table and construction bridge50 mm, clamping range approx. 47 to 53 mmShear force 200 kN, tensile force 10 kN, tightening torque 25 Nm28-4-0011-25
Countersunk clamping bolt, blackenedFixing the PRO angle stops and clamping squares65 mm, clamping range approx. 47 to 53 mmShear force 200 kN, tensile force 10 kN, tightening torque 50 Nm28-4-0009-25

You need 2 countersunk clamping bolts for each PRO clamping square. The squares concerned are listed on the page stops and clamping squares.

Using welding table clamps correctly in five steps

  1. Clean the holes

    Weld spatter and dirt in the holes stop bolts and clamps from seating properly. The hole brush with 30 mm diameter is made for 28 mm holes; more on this in the guide care and cleaning.

  2. Set the stop

    Place the stop or square and fix it in the table top with a quick-release clamping bolt.

  3. Position the workpiece

    Place the component against the stop and check its position on the grid.

  4. Position the clamp

    Insert the clamp into a hole close to the desired clamping point, swing the arm over the workpiece and tighten the spindle. The clamping height of the clamp must match the height of the component.

  5. Solve special cases

    If a part is pressure-sensitive or there is no counterhold, the magnetic clamping bolt clamps without tools.

Clamps and clamping bolts: quote or online shop

Screw clamps, quick-release clamping bolts and special bolts are listed with current price and availability in the online shop of die schmiede, multipacks in the special offers. The shop is in German and delivers within Germany only; for other countries, request a quote.

Request a quote Clamping tools in the shop (German)

Frequently asked questions

Which quick-release clamping bolt fits my welding table?

That depends on the thickness of the table top: for PRO tables with a 25 mm top, choose the quick-release clamping bolt with art. no. 28-4-0001-25, for Standard tables with 15 mm the one with art. no. 28-4-0001-15. Both have a 28 mm diameter and, according to the shop, a length of 95 mm. For tables from other manufacturers with a 28 mm system, measure the thickness of the top before ordering.

What clamping height do the professional screw clamps have?

The professional screw clamp 90° clamps up to 200 mm high, the version with high clamping range up to 340 mm and the professional screw clamp 45° up to 240 mm. All three are pushed through a 28 mm hole and can be rotated steplessly through 360°. Choose the clamp according to the height of the components you clamp most often.

What is a magnetic clamping bolt used for?

A magnetic clamping bolt clamps without tools and, according to the shop, is suitable for pressure-sensitive parts or places where no counterhold is possible. The magnetic clamping bolt from die schmiede is made of aluminium, 68 mm long, has a shank length of 25 mm and weighs 0.09 kg. The shop lists it for PRO welding tables with a 25 mm top.

How do connecting bolts differ from quick-release clamping bolts?

The quick-release clamping bolt holds stops and squares on the table and is locked by a twist lock with locking balls. At 50 mm, the connecting bolt is considerably shorter and creates a concealed connection between two components, for example a welding table and a construction bridge. Its clamping range is approx. 47 to 53 mm, and it is designed for PRO tables.

What our customers say

5.012 reviews on Google

All reviews on Google (opens in a new tab)

Reviews are shown in their original language (German). This is a selection of the most recent Google reviews with 4 or 5 stars and a written comment (up to 12). Reviews have not been checked for authenticity.